Discovering Plumbing Basics is Essential for Bathtub Installation
Discovering Plumbing Basics is Essential for Bathtub Installation
Blog Article
They are making several great pointers on the subject of How to Install a Bathtub Yourself overall in the content down the page.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also occasionally, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably difficult job. If the old tub is readily easily accessible, the task can move rapidly; if you have to open a wall to eliminate the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. See to it you have qualified yourself for the work and also are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed job, it is better to consider utilizing one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This short article will aid you mount a new tub in your restroom if you have currently gotten a brand-new bathtub and also don't require to change the setup of your previous supply of water pipelines.
Your tools and material list ought to consist of the following:
Getting ready for the Installation
Firstly, the supporting framework supplied with the bath should be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to stop pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome due to the limited gain access to that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. When the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Using both wooden boards under its feet, position the bath tub in the called for setting. The wooden boards are valuable in equally spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the tub till the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest versatile tap adapter to the appropriate supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the water supply and also examine all joints as well as brand-new pipework for leakages as well as tighten them if essential. Load the tub and also examine the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, fix the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bathtub should wait till the tub has been made use of a minimum of when as this will settle it right into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in location in between the tap as well as the sink. Safeguard the tap in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal tap ports. The former kind should be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a stiff seal, triggering the water to permeate the wall surface in between the bath and the tiling, resulting in complications with dampness and also feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes as well as cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily readily available on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our article about A Step-by-Step Guide to Installing a Bathtub. Thanks a lot for finding the time to read our piece of content. So long as you enjoyed reading our post if you please make sure you remember to share it. Thanks so much for going through it.
Instant fix? Dial! Report this page